Product Catalog
-----------------------------------------
High Nickel Alloys & Super Duplex Steel
-----------------------------------------
Pipes & Tubes
-----------------------------------------
Pipe Fittings
-----------------------------------------
Bar & Wire
-----------------------------------------
Sheets & Plates
-----------------------------------------
Instrument Fittings
-----------------------------------------
Flanges
-----------------------------------------
Other Non-Ferrous Metals
-----------------------------------------
Pipes/Tubes
-----------------------------------------
Hollow Sections
-----------------------------------------
Fittings/Flanges
-----------------------------------------
Plates/Sheets/Coils
-----------------------------------------
Hot Rolled Steel Plates
-----------------------------------------
Hot Rolled Steel Sheets
-----------------------------------------
Hot Rolled Coils
-----------------------------------------
Rods/Bars/Wires
-----------------------------------------
Bars For Oil & Gas
-----------------------------------------
Forged Round Bars
-----------------------------------------
Hexagon Bars
-----------------------------------------
Square Bars
-----------------------------------------
Cold Drawn Bars
-----------------------------------------
Forged Disk/Circles
-----------------------------------------
Structural Steels
-----------------------------------------
Flat Bars/Strips
-----------------------------------------
Studs/Bolts/Nuts
-----------------------------------------
Threaded Bars/Rods
-----------------------------------------
Fasteners
-----------------------------------------
SA193 B7 Stud Bolts
-----------------------------------------
SA193 B16 Stud Bolts
-----------------------------------------
SA194 2H HEX NUTS
-----------------------------------------
Corten Steels
-----------------------------------------
SAILCOR IRSM41
-----------------------------------------
Spring Steel Bars
-----------------------------------------
Boiler/PVQ Plates
-----------------------------------------
Structural Plates
-----------------------------------------
Alloy Steel Plates
-----------------------------------------
Shipbuilding Plates
-----------------------------------------
LRS Grade-A/B Plates
-----------------------------------------
ABS Grade-A/B Plates
-----------------------------------------
DNV Grade-A/B Plates
-----------------------------------------
BV Grade-A/B Plates
-----------------------------------------
SABS 1431:1987 Steels
-----------------------------------------
Q&T Steel Plates
-----------------------------------------
Plate Sizes & Grades
-----------------------------------------
SA516-60/70 HIC Tested
-----------------------------------------
SA516-60/70 Plates
-----------------------------------------
SA515-60/70 Plates
-----------------------------------------
ST52-3 DIN 17100
-----------------------------------------
S355J2G3 EN 10025-2
-----------------------------------------
S355K2G3 EN 10025-2
-----------------------------------------
S355J2+N EN 10025-2
-----------------------------------------
S355K2+N EN 10025-2
-----------------------------------------
EN 10025-2 Plates
-----------------------------------------
EN 10028-2/3 Plates
-----------------------------------------
Abrasion Resistant Steel
-----------------------------------------
Wear Resistant Steel
-----------------------------------------
Hardox 400/450 Plates
-----------------------------------------
Hardox 500/600 Plates
-----------------------------------------
Weldox 700 Plates
-----------------------------------------
SAILMA 350/350HI Plates
-----------------------------------------
SAILMA 410/410HI Plates
-----------------------------------------
SAILMA 450/450HI Plates
-----------------------------------------
Seamless Pipes/Tubes
-----------------------------------------
Welded Pipes/Tubes
-----------------------------------------
ERW/EFW Pipes/Tubes
-----------------------------------------
SAW/HFW Pipes
-----------------------------------------
ASTM A234/ASME SA234
-----------------------------------------
ASTM A403/ASME SA403
-----------------------------------------
ASTM A420/ASME SA420
-----------------------------------------
ASTM A860/ASME SA860
-----------------------------------------
Long Radius Bends
-----------------------------------------
Hot Induction Bends
-----------------------------------------
Forged Fittings
-----------------------------------------
Forged Flanges
-----------------------------------------
API 5L Line Pipes
-----------------------------------------
API 5L Gr.B PSL1/2 Pipes
-----------------------------------------
API 5L X42 PSL1/2 Pipes
-----------------------------------------
API 5L X46 PSL1/2 Pipes
-----------------------------------------
API 5L X52 PSL1/2 Pipes
-----------------------------------------
API 5L X56 PSL1/2 Pipes
-----------------------------------------
API 5L X60 PSL1/2 Pipes
-----------------------------------------
API 5L X65 PSL1/2 Pipes
-----------------------------------------
API 5L X70 PSL1/2 Pipes
-----------------------------------------
High Speed Steels
-----------------------------------------
Cold Work Tool Steels
-----------------------------------------
Hot Work Tool Steels
-----------------------------------------
Plastic Moulding Steels
-----------------------------------------
BS970 Specifications
-----------------------------------------
SAE Specifications
-----------------------------------------
JIS Specifications
-----------------------------------------
ASTM Standard Spec
-----------------------------------------
ASME Standard Spec
-----------------------------------------
Aerospace Alloys Spec
-----------------------------------------
Equivalent Grades
-----------------------------------------
Equivalent Standards
-----------------------------------------
Technical Specifications
-----------------------------------------
DIN Material No.
-----------------------------------------
Mechanical Properties
-----------------------------------------
Chemical Composition
-----------------------------------------
Density
-----------------------------------------
Trade Leads
-----------------------------------------
Contact Us
-----------------------------------------
Links
-----------------------------------------

EN 10028-2/3 Plates :

EN 10028-2/3 Plates Exporter

Contact Us For High Quality EN 10028-2/3 Plates

At JB Steel we pride ourselves on always putting the customer first. We help make stainless solutions simple for you by ensuring satisfaction through high delivery performance, flexibility and extensive service.

We are pleased to introduce ourselves as one of the leading Importers, Exporters, Suppliers & Stockists of EN 10028-2/3 Plates.

We would appreciate to get your esteemed enquires and look forward to the pleasure receiving your valuable response.

EN 10028-2/3 Plates

EN10028-2 / EN10028-3 PRESSURE VESSEL, FINE-GRAINED STEEL PLATES

EN10028-2 / EN10028-3 PRESSURE VESSEL, FINE-GRAINED STEEL PLATES

BS EN 10028-2 Hot Rolled Pressure Vessel Steel Plates

P235GH EN 10028-2 Hot Rolled Steel Plates - Available ex-stock
P265GH EN 10028-2 Hot Rolled Steel Plates - Available ex-stock 
P295GH EN 10028-2 Hot Rolled Steel Plates - Available ex-stock 
P355GH EN 10028-2 Hot Rolled Steel Plates - Available ex-stock

BS EN 10028-3 Hot Rolled Fine Grained Steel Plates

P275NH EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P275NL1 EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P275NL2 EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P355N EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P355NH EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P355NL1 EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P355NL2 EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P460NH EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P460NL1 EN 10028-3 Hot Rolled Steel Plates - Available ex-stock
P460NL2 EN 10028-3 Hot Rolled Steel Plates - Available ex-stock

Plates

PLATES OF STEELS ACCORDING TO EN 10025-2

The most commonly used structural steels having minimum yield strength min. 235 MPa and guaranteed weldability that can be used for low demanding steel structures for bridges, halls, parts of railway and motor vehicles, etc.

DesignationMin. Yield
Strength ReH 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - longitudinalCEV max.1)Dimension
Table No.Max.
Thickness
[mm]
 

Max. Thickness
for option (C)
[mm]

S235JR(C)235360-51024+20/270,35Table 1 80 3)

30 4)

S235J0(C)235360-510240/270,35Table 1 80 3)

30 4)

S235J2(C)235360-51024-20/270,35Table 1 80 3)

30 4)

S275JR(C)275410-56021+20/270,40Table 1 80 3)

30 4)

S275J0(C)275410-560210/270,40Table 1 80 3)

30 4)

S275J2(C)275410-56021-20/270,40Table 1 80 3)

30 4)

S355JR(C)355470-63020+20/270,45Table 1 80 3)

30 4)

S355J0(C)355470-630200/270,45Table 1 80 3)

30 4)

S355J2(C)355470-63020-20/270,45Table 1 80 3)

30 4)

S355K2(C)355470-63020-20/400,45Table 1 80 3)

30 4)

1) CEV= CEV ; valid for thickness up to 30 mm, for higher thickness refer to the standard
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
3) Higher thickness on agreement
4) Under standard 
EQUIVALENT DESIGNATION


EN 10025-2EN 10025+A1DIN 17100BS 4360

NFA 35-501

S235JR(C)S235JRG2(C)RSt 37 - 240 B

E 24 - 2

S235J0(C)S235J0(C)St 37 - 3U40 C

E 24 - 3

S235J2(C)S235J2G4(C)St 37 - 3N40 D

E 24 - 4

S275JR(C)S275JR(C)St 44 - 243 B

E 28 - 2

S275J0(C)S275J0(C)St 44 - 3U43 C

E 28 - 3

S275J2(C)S275J2G4(C)St 44 - 3N43 D

E 28 - 4

S355JR(C)S355JR(C)-50 B

E 36 - 2

S355J0(C)S355J0(C)St 52 - 3U50 C

E 36 - 3

S355J2(C)S355J2G4(C)St 52 - 3N50 D

-

S355K2(C)S355K2G4(C)-50 DD

E 36 - 4

PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10025-3

Structural steels with guaranteed fine grain structure and low carbon equivalent. Because of the yield strength up to 460 MPa and impact energy guaranteed at temperature -50 °C these steels are suitable for more demanding steel structures and their supporting elements. They are suitable for construction of railway and motor vehicles, too.

Designation

Min. Yield
Strength ReH 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - longitudinalCEV max. 1)Dimension
Table No.

 Max.
Thickness
[mm]

S275N (NL)

275370-51024-20/40
(-50/27)0.40table 1

 80 3)
 

S355N (NL)

355470-63022-20/40
(-50/27)0.43table 1

 80 3)
 

S420N (NL)

420520-68019-20/40
(-50/27)0.48table 1

 80

S460N (NL)

460550-72017-20/40
(-50/27)0.53table 2

 80

1) CEV= CEV; valid for thickness up to 63 mm; for higher thickness refer to the standard
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
3) Higher thickness on agreement


EQUIVALENT DESIGNATION


EN 10025-3EN 10113-2

DIN 17102

S275NS275N

StE 285

S275NLS275NL

TStE 285

S355NS355N

StE 355

S355NLS355NL

TStE 355

S420NS420N

StE 420

S420NLS420NL

TStE 420

S460NS460N

StE 460

S460NLS460NL

TStE 460

THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10025-4
Thermomechanical rolled plates of structural steels having low carbon equivalent, and thus an excellent weldability. They are used for more demanding steel structures and their supporting elements. The impact energy is guaranteed also at temperature -50 °C which facilitates a wide range for their usage.

DesignationMin. Yield
Strength ReH 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - longitudinalCEV max. 1)Dimension
Table No.

Max.
Thickness
[mm]

S275M (ML)275370-53024-20/40 (-50/27)0.34table 3

40

S355M (ML)355470-63022-20/40 (-50/27)0.39table 3

40

S420M (ML)420520-68019-20/40 (-50/27)0.43table 3

30 3)

S460M (ML)460540-72017-20/40 (-50/27)0.45table 3

22 3)

1) CEV= CEV; valid for thickness up to 63 mm; for higher thickness refer to the standard
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
3) Higher thickness on agreement
EQUIVALENT DESIGNATION


EN 10025-4EN 10113-3

SEW 092

S275MS275M

-

S275MLS275ML

-

S355MS355M

QStE 380 TM

S355MLS355ML

-

S420MS420M

QStE 420 TM

S420MLS420ML

-

S460MS460M

QStE 460 TM

S460MLS460ML

-

PLATES OF STEELS ACCORDING TO ASTM


DesignationGradeMin. Yield
Strength
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
200/50
[%]Min. Impact
Energy KV 1)
[°C/J] - longitudinalDimension
Table No.

Max. Thickness [mm]

A 36250400-55020/232)table 1

80

A 283

A165310-41527/302)table 1

80

B185345-45025/282)table 1

80

C205380-51522/252)table 1

80

D230415-55020/232)table 1

80

A 529

50 (345)345485-69018/212)table 1

25 3)

55 (380)380485-69017/202)table 1

25 3)

Maximum value of the carbon equivalent as per the formula CEV on agreement
1) Testing on agreement
2) Testing temperature and minimum impact energy on agreement
3) Under standard

FINE-GRAIN STEELS ACCORDING TO ASTM

DesignationGradeMin. Yield
Strength
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
200/50
[%]Min. Impact
Energy KV 1)
[°C/J] - longitudinalDimension
Table No.

Max. Thickness [mm]

A 572
(type 1,2,3)

42(290)

290415 min.20/242)table 1

80

50(345)

345450 min.18/212)table 1

80

55(380)

380485 min.17/202)table 1

50 3)

60(415)

415520 min.16/182)table 1

32 3)

A 573

58(400)

220400-49021/242)table 1

40 3)

65(450)

240450-53020/232)table 1

40 3)

70(485)

290485-62018/212)table 1

40 3)

A 633

A

290430-57018/23-60/20table 1

80

C

345485-62018/23-60/20table 1

80

D

345485-62018/23-60/20table 1

80

E

415550-69018/23-60/20table 2

80

Maximum value of the carbon equivalent as per the formula CEV on agreement
1) Testing on agreement
2) Testing temperature and minimum impact energy on agreement
3) Under standard

PLATES OF STEELS ACCORDING TO 10025-5


Designation

Min. Yield
Strength ReH 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - longitudinalCEV max. 1)Dimension
Table No.

 Max.
Thickness
[mm]

S235J0W

235360-510240/270,44table 1

 80

S235J2W

235360-51024-20/270,44table 1

 80

S355J0WP 3)

355470-630200/270,52table 1

 12 3)

S355J2WP 3)

355470-63020-20/270,52table 1

 12 3)
 

S355J0W

355470-630200/270,52table 1

 80

S355J2W

355470-63020-20/270,52table 1

 80

S355K2W

355470-63020-20/400,52table 1

 80

1) CEV= CEV
2) Valid for plates with thickness up to 16 mm, for higher thickness refer to the standard
3) Under standard


EQUIVALENT DESIGNATION


EN 10025-5EN 10155SEW 087

CAN/CSA - G40.21-M

S235J0WS235J0W-

-

S235J2WS235J2WWTSt 37 - 3

-

S355J0WPS355J0WP-

-

S355J2WPS355J2WP-

-

S355J0WS355J0W-

-

S355J2WS355J2G2WWTSt 52 - 3

350AT

S355K2WS355K2G2W-

-

PLATES MADE OF STEELS ACCORDING TO ASTM


DesignationGradeMin. Yield
Strength
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
200/50
[%]Min. Impact
Energy KV1)
[°C/J] - longitudinalDimension
Table No.

 Max.
Thickness
[mm]

A 588

A345485 min.18/212)table 1

 80

B345485 min.18/212)table 1

 80

C345485 min.18/212)table 1

 80

K345485 min.18/212)table 1

 80

Maximum value of the carbon equivalent as per the formula CEV on agreement
1) Testing on agreement
2) Testing temperature and minimum impact energy on agreement

NORMALIZED PLATES OF STEELS ACCORDING TO EN 10225


DesignationGroupMin. Yield
Strength ReH 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - longitudinalCEV max. 3)Pcm max. 4)Dimension
Table No.

Max.
Thickness
[mm]

S355G2+N1355 1)470 - 63022-20/50 7)0,43...table 1

20 5)

S355G3+N1355 1)470 - 63022-40/50 7)0.43...table 1

40 5)

S355G7+N2355 2)470 - 63022-40/50 8)0.430,24table 1

62 6)

S355G8+N3355 2)470 - 63022-40/50 8)0.430,24table 1

62 6)

S355G9+N2355 2)470 - 63022-40/50 8)0.430,22table 1

62 6)

S355G10+N3355 2)470 - 63022-40/50 8)0.430,22table 1

62 6)

1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) Valid for thickness up to 25 mm, for higher thickness refer to the standard
3)
4)
5) Under standard
6) Higher thickness up to 75 mm on agreement
7) Longitudinal
8) Transverse

PLATES FOR PIPES ACCORDING TO API 5L 1) AND EN 10208-2 1) ( SWEET SERVICE )

Grade acc. API-5LDesignation acc. EN 10208-2Yield Strength Rt0,5 (Rt0,2) 2)
[MPa]Tensile
Strength Rm 2)
[MPa]Min.
Elongation 2)
[%]CEV max. 2)Dimension
Table No.

Max.
Thickness 3)
[mm]

BL245MB245-440415-760220,40table 4

30

X 42L290MB290-440415-760210,40table 4

30

X 46320-525435-760200,41table 4

22

X 52L360MB360-510460-760200,41table 4

22

X 56390-545490-760180,42table 4

22

X 60L415MB415-565520-760180,42table 4

22

X 65L450MB450-570535-760180,43table 4

22

X 70L485MB485-605570-760180,43table 4

22

1) Standards API 5L and EN 10208 are technical conditions for supplies of welded pipes, not for plates
2) Informative value
3) Higher thickness on agreement
4) Supplied with HIC and SSC tests as per NACE or EN standard

PLATES FOR PIPES ACCORDING TO API 5L 1) AND EN 10208-2 1) ( SOUR SERVICE 4) )

Grade acc. API-5LDesignation acc. EN 10208-2Yield Strength Rt0,5 (Rt0,2) 2)
[MPa]Tensile
Strength Rm 2)
[MPa]Min.
Elongation 2)
[%]CEV max. 2)Dimension
Table No.

Max.
Thickness 3)
[mm]

BL245MB245-440415-760220,40table 4

30

X 42L290MB290-440415-760210,40table 4

30

X 46320-525435-760200,41table 4

22

X 52L360MB360-510460-760200,41table 4

22

X 60L415MB415-565520-760180,42table 4

22

X 65L450MB450-570535-760180,43table 4

22

1) Standards API 5L and EN 10208 are technical conditions for supplies of welded pipes, not for plates
2) Informative value
3) Higher thickness on agreement
4) Supplied with HIC and SSC tests as per NACE or EN standard

PLATES ACCORDING TO INDIVIDUAL SHIPPING COMPANIES


Steel GroupMin.
Yield Strength ReH
[MPa]Min.
Impact Energy KV
[°C/J] – longitudinalABS – American
Bureau of ShippingBV – Bureau VeritasČLPR – Czech Shipping
and Industrial registerGL – Germanischer LloydDNV – Det Norske VeritasLR – Lioyd's Register
of ShippingRINA –
Registro Italiano NavalePC – Morskoj Registr
Sudochodstva

Rozměrová tabulka číslo

Normal Strength
Steel Grades

235

-AAAAAAA/24A

table 1

0/27BBBBBBS/24B

table 1

-20/27DDDDDDSS/24D

table 1

-40/27EEEEEEE/24E

table 1

High Strength
Steel Grades

315

0/31A 32A 32A 32A 32A 32AH 32S/32A 32

table 1

-20/31D 32D 32D 32D 32D 32DH 32SS/32D 32

table 1

-40/31E 32E 32E 32E 32E 32EH 32E/32E 32

table 1

355

0/34AH 36AH 36A 36A 36A 36AH 36S/36A 36

table 1

-20/34DH 36DH 36D 36D 36D 36DH 36SS/36D 36

table 1

-40/34EH 36EH 36E 36E 36E 36EH 36E/36E 36

table 1

Maximum value of the carbon equivalent as per the formula CEV rovnice on agreement

PLATES ACCORDING TO ASTM A 131

DesignationGradeMin. Yield
Strength
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
200/50
[%]Min. Impact
Energy KV
[°C/J] - longitudinalDimension
Table No.

Max. Thickness [mm]

A 131

A235400-49021/24+20/27table 1

80

B235400-49021/240/27table 1

80

D235400-49021/24-10/27table 1

80

E235400-49021/24-40/27table 1

80

CS235400-49021/24-40/27table 1

80

DS235400-49021/24-10/27table 1

80

AH 32315470-58519/220/34table 1

80

DH 32315470-58519/22-20/34table 1

80

EH 32315470-58519/22-40/34table 1

80

AH 36360490-62019/220/34table 1

80

DH 36360490-62019/22-20/34table 1

80

EH 36360490-62019/22-40/34table 1

80

Maximum value of the carbon equivalent as per the formula CEV rovnice on agreement
1) Valid for thickness up to 50 mm, for higher thickness refer to the standard

THERMOMECHANICAL ROLLED PLATES OF STEELS ACCORDING TO EN 10149-2
Standard methods used for processing these plates are bending, fl anging, cold roll forming, etc. Based on agreement these plates can be delivered in the condition suitable for hot-dip zinc-coating. These plates have excellent weldability because of low carbon equivalent.


Designation

Min. Yield
Strength ReH
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV 1)
[°C/J] - longitudinalTransverse
Bend Test 2)Dimension
Table No.

Max.
Thickness
[mm]

S315MC

315390-51024-20/400 ttable 3

20 3)

S355MC

355430-55023-20/400.5 ttable 3

20 3)

S420MC

420480-62019-20/400.5 ttable 3

20 3)

S460MC

460520-67017-20/401 ttable 3

20 3)

S500MC

500550-70014-20/401 ttable 3

16 3)

S550MC

550600-76014-20/401.5 ttable 3

16 3)

Maximum value of the carbon equivalent as per the formula  CEV   on agreement
1) Testing on agreement
2) Minimum former diameter for 180° bend angle; t – plate thickness
3) Under standard
EQUIVALENT DESIGNATION


EN 10149-2
 

SEW 092

S315MC

(QStE 340 TM)

S355MC

(QStE 380 TM)

S420MC

QStE 420 TM

S460MC

QStE 460 TM

S500MC

QStE 500 TM

S550MC

QStE 550 TM

NORMALIZED (ROLLED) PLATES OF STEELS ACCORDING TO EN 10149-3
These plates guarantee suitability for cold forming because of their technological processing. Standard methods used for processing these plates are bending, fl anging, cold roll forming, etc. Based on agreement these plates can be delivered in the condition suitable for hot-dip zinc-coating.


Designation

Min. Yield
Strength ReH
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV 1)
[°C/J] - longitudinalTransverse
Bend Test 2)Dimension
Table No.

Max.
Thickness
[mm]

S260NC

260370-49030-20/400 ttable 1

20 3)

S315NC

315430-55027-20/400,5 ttable 1

20 3)

S355NC

355470-61025-20/400,5 ttable 1

20 3)

S420NC

420530-67023-20/400,5 ttable 2

20 3)

Maximum value of the carbon equivalent as per the formula  CEV on agreement
1) Testing on agreement
2) Minimum former diameter for 180° bend angle; t – plate thickness
3) Under standard
EQUIVALENT DESIGNATION


EN10149-3

SEW 092

S260NC

QStE 260N

S315NC

(QStE 340N)

S355NC

(QStE 380N)

S420NC

QStE 420N

PLATES OF STEELS ACCORDING TO EN 10083-2 AND EN 10083-3

Používají se na strojní součásti ve všech oblastech strojírenské výroby. Ve většině případů jsou obtížně svařitelné. Jsou dodávány ve stavu žíhaném na měkko (+A) nebo normalizovaném (+N) podle následující tabulky. Výrobky z plechů se dále zpracovávají tzv. zušlechťováním (obvykle kalení a popouštění), teprve po něm získávají své typické vlastnosti, tj. vysokou houževnatost, tvrdost a pevnost.


Designation

Min. Yield
Strength ReH 1)
[MPa]Min. Tensile
Strength Rm 1)
[MPa]Min. Elongation
L0
[%]HB max.
(+A)Dimension
Table No.

Max. Thickness [mm]

C22E 2)

24043024-tabulka 1

80

C35/C35E 2)

30055018-table 2

80

C40/C40E 2)

32058016-table 2

80

C45/C4E 2)

34062014207table 2

80

C50E 2)

35565013217table 2

80

C55/C55E 2)

37068011229table 2

80

C60/C60E 2)

38071010241table 2

80

28Mn6 2)

34563017223table 2

80

38Cr2 3)

---207table 2

80

46Cr2 3)

---223table 2

80

34Cr4 3)

---223table 2

80

37Cr4 3)

---235table 2

80

41Cr4 3)

---241table 2

80

25CrMo4 3)

---212table 2

80

34CrMo4 3)

---223table 2

80

42CrMo4 3)

---248table 2

80

50CrMo4 3)

---248table 2

80

34CrNiMo6 3)

---248table 2

80

30CrNiMo8 3)

---223table 2

80

35NiCr6 3)

---240table 2

80

39NiCrMo3 3)

---248table 2

80

51CrV4 3)

----table 2

80

20MnB5 3) 4)

----tabulka 2

80

30MnB5 3) 4)

----table 2
 

80

38MnB5 3) 4)

----table 2

80

27MnCrB5-2 3) 4)

----table 2

80

33MnCrB5-2 3) 4)

----table 2

80

39MnCrB6-2 3) 4)

----table 2

80

1) Valid for plates in normalized condition and for thickness up to 16 mm, for higher thickness refer to the standard
2) EN 10083-2
3) EN 10083-3
4) Plates without heat treatment
EQUIVALENT DESIGNATION


ENGermany

Great Britain
 

C22ECK22

070M20

C35/C35EC35/CK35

080M36

C40/C40EC40/CK40

080M40

C45/C45EC45/CK45

080M46

C50ECK50

080M50

C55/C55EC55/CK55

070M55

C60/C60EC60/CK60

070M60

28Mn628Mn6

150M19

38Cr238Cr2

-

46Cr246Cr2

-

34Cr434Cr4

530M32

37Cr437Cr4

530M36

41Cr441Cr4

530M40

25CrMo425CrMo4

708M25

34CrMo434CrMo4

708M32

42CrMo442CrMo4

708M40

50CrMo450CrMo4

708M50

34CrNiMo634CrNiMo6

817M40

30CrNiMo830CrNiMo8

823M30

35NiCr635NiCr6

-

PLATES OF STEELS ACCORDING TO DESIGNATION A 827, A 829, A 830


DesignationGrade (SAE Number)

Dimension table number

A 827

1009

table 1

1020

table 1

1035

table 2

1040

table 2

1045

table 2

1050

table 2

A 829

1330

table 2

1335

table 2

1340

table 2

1345

table 2

4118

table 2

4130

table 2

4135

table 2

4137

table 2

4140

table 2

4142

table 2

4145

table 2

4150

table 2

4340

table 2
 

4615

table 2

4617

table 2

4620

table 2

8615

table 2

8617

table 2

9620

table 2

8622

table 2

8625

table 2

8627

table 2

8630

table 2

8637

table 2

8640

table 2

8742

table 2

A 830

1006

table 1

1008

table 1

1009

table 1

1010

table 1

1012

table 1

1015

table 1

1016

table 1

1017

table 1

1018

table 1

1019

table 1

1020

table 1

1021

table 1

1022

table 1

1023

table 1

1025

table 1

1026

table 1

1030

table 1

1033

table 1

1035

table 2

1037

table 2

1038

table 2

1039

table 2

1040

table 2

1042

table 2

1043

table 2

1045

table 2

1046

table 2

1049

table 2

1050

table 2

1055

table 2

1060

table 2

1524

table 2

1527

table 2

1536

table 2

1541

table 2

1548

table 2

1552

table 2

Heat treatment and mechanical properties an agreement

PLATES OF STEELS FOR SIMPLE PRESSURE VESSELS ACCORDING TO EN 10207

Plates with low yield strength for simple pressure vessels and storage facilities, e.g. for compressed air or other fl uids operating under normal outdoor temperatures.


Designation

Min. Yield
Strength ReH 1)
[MPa]Min. Yield
Strength RpO,2 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - longitudinal

Dimension
Table No.

P235S

235117360-48026-20/28

table 1

P265S

265140410-53022-20/28

table 1

P275SL

275132390-51024-50/28

table 1

1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) Valid for temperature 300 °C, for other temperatures (lower) refer to the standard

PLATES OF STEELS ACCORDING TO EN 10028-2
Plates of unalloyed as well as alloyed steels for pressure loaded vessels and facilities, operating under normal as well as elevated temperatures. These plates are usually delivered in normalized condition or in normalized and tempered condition.


DesignationMin. Yield
Strength ReH 1)
[MPa]Min. Yield
Strength R pO,2 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV 3)
[°C/J] - transverse

Dimension
Table No.

P235GH 4)235153360-48024-20/27

table 1

P265GH 4)265173410-53022-20/27

table 1

P295GH 4)295192460-58021-20/27

table 1

P355GH 4)355232510-65020-20/27

table 1

16Mo3275194440-59022+20/31

table 1

18MnMo4-5345285510-65020-20/27

table 1

15NiCuMoNb5-6-4460380610-78016-20/27

table 2

13CrMo4-5300216450-60019+20/31

table 1

13CrMoSi5-5310233510-690200/27

table 1

10CrMo9-10310236480-63018+20/31

table 1

12CrMo9-10355295540-69018-20/27

table 2

1) Valid for plates with thickness up to 16 mm, for thicker plates refer to the standard
2) On agreement with the order; valid for temperature 300 °C and thickness up to 16 mm for other temperatures or thicker plates refer to the standard
3) For other temperatures refer to the standard or on agreement
4) Maximum value of the carbon equivalent on agreement when ordering for steel grades P235GH, P265GH, P295GH and P355GH based on the following formula:
CEV= CEV
EQUIVALENT DESIGNATION


ENČSN

DIN 17155

P235 GH11368

H I

P265 GH11418

H II

P295 GH13030 (11478)

17Mn4

P355 GH11523

19Mn6

16Mo315020

15Mo3

13CrMo4-515121

13CrMo44

10CrMo9-1015313

10CrMo910

18MnMo4-515223 (15219)

-

PLATES OF FINE-GRAINED STEELS ACCORDING TO EN 10028-3
These steels feature guaranteed fine grain structure and low carbon equivalent. Mechanical properties of these plates are guaranteed at high temperatures (up to 400 °C) – yield strength Rp0,2 as well as at low temperatures (down to -50 °C) – impact energy KV; therefore, they can be used for constructions of more demanding pressure vessels working under high as well as low temperatures.


DesignationMin. Yield
Strength ReH 1)
[MPa]Min. Yield
Strength RpO,2 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV 3)
[°C/J] - transverseCEV max. 4)

Dim.
Table
No.

P275NH275179390-51024-20/300.40

table 1

P275NL1275179390-51024-40/270.40

table 1

P275NL2275179390-51024-50/270.40

table 1

P355N355-490-63022-20/300.43

table 1

P355NH355232490-63022-20/300.43

table 1

P355NL1355232490-63022-40/700.43

table 1

P355NL2355232490-63022-50/270.43

table 1

P460NH460300570-72017-20/300.53

table 2

P460NL1460300570-72017-40/270.53

table 2

P460NL2460300570-72017-50/270.53

table 2

1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) By agreement with the order; valid for temperature 300 °C and thickness up to 16 mm, for other temperatures and/or higher thickness refer to the standard
3) For other temperatures refer to the standard
4) On agreement; CEV=CEV; valid for thickness up to 60 mm, for thicker plates refer to the standard
EQUIVALENT DESIGNATION

ENČSN

DIN 17102

P275NH11448

WStE 285

P275NL111449

TStE 285

P275NL2-

EStE 285

P355N-

StE 355

P355NH-

WStE 355

P355NL111503

TStE 355

P355NL2-

EStE 355

P460NH-

WStE 460

P460NL1-

TStE 460

P460NL2-

EStE 460

THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-5
Thermomechanical rolled plates having higher yield strength up to 460 MPa are designed for pressure vessels and facilities working under normal or low temperatures. These plates have excellent weldability because of low carbon equivalent. Impact energy is guaranteed even at temperature -50 °C.


Designation

Min. Yield
Strength ReH
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV 3)
[°C/J] - transverseCEV max. 4)Dimension
Table No.

Max.
Thickness
[mm]

P355M

355 1)450-61022-20/270,39Table 3

40

P355ML1

355 1)450-61022-40/270,39Table 3

40

P355ML2

355 1)450-61022-50/270,39Table 3

40

P420M

420 2)500-66019-20/270,43Table 3

30 5)

P420ML1

420 2)500-66019-40/270,43Table 3

30 5)

P420ML2

420 2)500-66019-50/270,43Table 3

30 5)

P460M

460 2)530-72017-20/270,45Table 3

22 5)

P460ML1

460 2)530-72017-40/270,45Table 3

22 5)

P460ML2

460 2)530-72017-50/270,45Table 3

22 5)

1) Valid for thickness up to 40 mm, for higher thickness refer to the standard
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
3) For other temperatures refer to the standard
4) On agreement; CEV= CEV ; valid for thickness up to 16 mm, for thicker plates refer to the standard
5) Higher thickness on agreement

PLATES OF STEELS ACCORDING TO ASTM


DesignationGradeMin. Yield
Strength
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
200/50
[%]Min. Impact
Energy KV 1)
[°C/J] - longitudinal

Dimension
Table No.

A 202

A310515-65516/192)

table 1

B325585-76015/182)

table 2

A 204

A255450-58519/232)

table 1

B275485-62017/212)

table 1

C295515-65516/202)

table 1

A 285

A165310-45027/304/14

table 1

B185345-48525/2810/14

table 1

C205380-51523/2716/14

table 1

A 387

2310485-62018/222)

table 2

11310515-69018/222)

table 1

12275450-58519/222)

table 1

22310515-690-/182)

table 1

A 455260515-65515/22-4/18

table 1

A 515

60 (415)220415-55021/252)

table 1

65 (450)240450-58519/232)

table 1

70 (485)260485-62017/212)

table 1

On agreement, carbon equivalent guarantee is available as per the following formulaCEV
1) Impact energy testing on agreement
2) Testing temperature and minimum impact energy on agreement

FINE-GRAIN STEELS


DesignationGradeMin. Yield
Strength
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
200/50
[%]Min. Impact
Energy KV 1)
[°C/J] - longitudinal

Dimension
Table No.

A 225D415550-72517/192)

table 2

A 299290515-65516/19-7/20

table 1

A 302

A310515-65515/192)

table 1

B345550-69015/182)

table 2

C345550-69017/202)

table 2

D345550-69017/202)

table 2

A 516

55 (380)205380-51523/27-51/18

table 1

60 (415)220415-55021/25-51/18

table 1

65 (450)240450-58519/23-51/18

table 1

70 (485)260485-62017/21-46/20

table 1

A 537 class 1345485-62018/22-62/20

table 1

A 612345570-72516/22-46/27

table 2

A 662

A275400-54020/23-60/18

table 1

B275450-58520/23-51/18

table 1

C295485-62018/22-46/20

table 1

A 737

B345485-62018/232)

table 1

C415550-69018/232)

table 2

On agreement, carbon equivalent guarantee is available as per the following formulaCEV
1) Impact energy testing on agreement
2) Testing temperature and minimum impact energy on agreement

THERMOMECHANICAL ROLLED PLATES OF STEELS ACCORDING TO EN 10225


DesignationGroupMin. Yield
Strength ReH 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - longitudinalCEV max. 3)Pcm max. 4)Dimension
Table No.

Max.
Thickness
[mm]

S355G5+M1355 1)470 - 63022-20/50 7)0,43...table 3

20 5)

S355G6+M1355 1)470 - 63022-40/50 7)0.43...table 3

40 5)

S355G7+M2355 2)470 - 63022-40/50 8)0.430,24table 3

40

S355G8+M3355 2)470 - 63022-40/50 8)0.430,24table 3

40

S355G9+M2355 2)470 - 63022-40/50 8)0.410,21table 3

40

S355G10+M3355 2)470 - 63022-40/50 8)0.410,21table 3

40

S420G1+M2420 1)500 - 60019-40/60 8)0,420,22table 3

30

S420G2+M3420 1)500 - 66019-40/60 8)0,420,22table 3

30

S460G1+M2460 1)540 - 700 1)17-40/60 8)0,430,22table 3

30

S460G2+M3460 1)540-700 1)17-40/60 8)0,430,22table 3

30

1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) Valid for thickness up to 25 mm, for higher thickness refer to the standard
3)
4)
5) Under standard
6) Higher thickness up to 75 mm on agreement
7) Longitudinal
8) Transverse

PLATES MADE OF STEELS ACCORDING TO API 2H
Plates made of the steel grades listed below are used for offshore structures. These steel grades show especially good impact resistance, fatigue resistance and lamellar cracking resistance.


GradeMin. Yield
Strength
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] - transverseCEV max. 1)Dimension
Table No.

Max.
Thickness
[mm]
 

42289427-56518/22-40/34

0,43 2)

table 1

 80

0,45 3)

50

345 2)

483-62016/21-40/41

0,43 4)

table 2

 80

324 3)

0,45 5)

1) CEV= CEV
2) For widht to 2 1/2"
3) For widht over 2 1/2"
4) For widht to 2"
5) For widht over 2"

PLATES OF STEELS ACCORDING TO EN 10084


Designation

HB max.
(+A)
 Dimension
Table No.

Max.
Thickness
[mm] 
 

C10E

131table 1

80

C15E

143table 1

80

C16E

156table 1

80

17Cr3

174table 1

80

28Cr4

217table 2

80

16MnCr5

207table 2

80

16MnCrB5

207table 2

80

20MnCr5

217table 2

80

18CrMo4

207table 2

80

20MoCr3

217table 2

80

20MoCr4

207table 2

80

16NiCr4

217table 2

80

10NiCr5-4

192table 2

80

18NiCr5-4

223table 2

80

17CrNi6-6

229table 2

80

20NiCrMo2-2

212table 2

80

17NiCrMo6-4

229table 2

80

18CrNiMo7-6

229table 2

80

PLATES OF STEELS ACCORDING TO EN 10085
These plates are supplied only in soft annealed (+A) condition.


Designation

HB max.
(+A)
 Dimension Table No.

Thickness 1) [mm]

24CrMo13-6

248table 2

20-80

31CrMo12

248table 2

20-80

31CrMoV9

248table 2

20-80

33CrMoV12-9

248table 2

20-80

1) Other thickness on agreement

PLATES OF STEELS ACCORDING TO EN ISO 4957
 These plates are supplied only in soft annealed (+A) condition.


Designation

HB max. (+A)
 Dimension Table No.

Thickness 1) [mm]

C45U

207table 2

10-80

C70U

183table 2

20-80

C80U

192table 2

20-80

C90U

207table 2

20-80

21MnCr5

217table 2

20-80

70MnMoCr8

248table 2

20-80

90MnCrV8

229table 2

20-80

35CrMo7

260table 2

20-80

40CrMnNiMo8-6-4

260table 2

20-80

55NiCrMoV7

248table 2

20-80

1) Other thickness on agreement

PLATES OF STEELS FOR SIMPLE PRESSURE VESSELS ACCORDING TO EN 10207
Plates with low yield strength for simple pressure vessels and storage facilities operating under normal outdoor temperatures, e.g. for compressed air or other fluids.


Designation

Min. Yield
Strength ReH 1)
[MPa]Min. Yield
Strength RpO,2 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
 [°C/J] – longitudinalDimension
Table No. 

Max.
Thickness
[mm] 
 

P235S

235117360-48026-20/28table 1

60 3)
 

P265S

265140410-53022-20/28table 1

60 3)

P275SL

275132390-51024-50/28table 1

60 3)

1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) Valid for temperature 300 °C, for other temperatures (lower) under standard refer to the standard
3) Under standard

PLATES OF STEELS ACCORDING TO EN 10028-2
Plates of unalloyed as well as alloyed steels for pressure loaded vessels and facilities, operating under normal as well as elevated temperatures. These plates are usually delivered in normalized condition or in normalized and tempered condition.


DesignationMin. Yield
Strength ReH 1)
[MPa]Min. Yield
Strength RpO,2 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV 3)
[°C/J] – transverseDimension
Table No.

Max.
Thickness
[mm]
 

 

P235GH 4)235153360 - 48024-20/27table 1

80 5)
 

P265GH 4)265173410 - 53022-20/27table 1

80 5)

P295GH 4)295192460 - 58021-20/27table 1

80 5)

P355GH 4)355232510 - 65020-20/27table 2

80 5)

16Mo3275194440 - 59022+20/31table 1

80

18MnMo4-5345285510 - 65020-20/27table 1

80

15NiCuMoNb5-6-4460380610 - 78016-20/27table 2

80

13CrMo4-5300216450 - 60019+20/31table 1

80

13CrMoSi5-5310233510 - 690200/27table 1

80

10CrMo9-10310236480 - 63018+20/31table 1

80

12CrMo9-10355295540 - 69018-20/27table 2

80

1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) Testing on agreement; valid for temperature 300 °C and thickness up to 16 mm; for other temperatures u
to the standard
3) For other temperatures under standard refer to the standard or on agreement
4) Maximum value of the carbon equivalent as per the formula CEV rovniceon agreement
5) Higher thickness up to 100 mm on agreement
  
EQUIVALENT DESIGNATION


EN10028-2

DIN 17155

P235 GH

H I

P265 GH

H II

P295 GH

17Mn4

P355 GH

19Mn6

16Mo3

15Mo3

13CrMo4-5

13CrMo44

10CrMo9-10

10CrMo910

18MnNo4-5

-

PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-3
These steels feature guaranteed fi ne-grain structure and low carbon equivalent. Mechanical properties of these plates are guaranteed at
high temperatures (up to 400 °C) – yield strength Rp0,2 as well as at low temperatures (down to -50 °C) – impact energy KV; therefore,
they can be used for constructions of more demanding pressure vessels working under high as well as low temperatures.


DesignationMin. Yield
Strength ReH 1)
[MPa]Min. Yield
Strength RpO,2 2)
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV
[°C/J] – transverseCEV max. 4)Max.
Thickness
[mm]
 

Dimension
Table No.

P275NH275179390-51024-20/300,40805)

table 1

P275NL1275179390-51024-40/270,40805)

table 1

P275NL2275179390-51024-50/270,40805)

table 1

P355N355-490-63022-20/300,43805)

table 1

P355NH355232490-63022-20/300,43805)

table 1

P355NL1355232490-63022-40/270,43805)

table 1

P355NL2355232490-63022-50/270,43805)

table 1

P460NH460300570-72017-20/300,5380

table 2

P460NL1460300570-72017-40/270,5380

table 2

P460NL2460300570-72017-50/270,5380

table 2

1) Valid for thickness up to 16 mm, for higher thickness refer to the standard
2) Testing on agreement; valid for temperature 300 °C and thickness up to 16 mm, for other temperatures under standard or higher thickness refer
to the standard
3) For other temperatures under standard refer to the standard
4) On agreement; CEV = CEV rovnice  ; valid for thickness up to 60 mm, for higher thickness refer to the standard
5) Higher thickness up to 100 mm on agreement

EQUIVALENT DESIGNATION

EN10028-3

DIN 17102

P275NH

WStE 285

P275NL1

TStE 285

P275NL2

EStE 285

P355N

StE 355

P355NH

WStE 355

P355NL1

TStE 355

P355NL2

EStE 355

P460NH

WStE 460

P460NL1

TStE 460

P460NL2

EStE 460

THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-5
Thermomechanical rolled plates having higher min. yield strength up to 460 MPa are designed for pressure vessels and facilities working under normal or low temperatures. These plates have excellent weldability because of low carbon equivalent. Impact energy is guaranteed even at temperature -50 °C.


DesignationMin. Yield
Strength ReH
[MPa]Min. Yield
Strength Rm
[MPa]Tensile
Strength Rm
[MPa]Min. Elongation
L0
[%]Min. Impact
Energy KV 3)
[°C/J] – transverseCEV max. 4)Dimension
Table No.

Max.
Thickness
[mm]
 

P355M

355 1)450-61022-20/270,39table 3

40

P355ML1

355 1)450-61022-40/270,39table 3

40

P355ML2

355 1)450-61022-50/270,39table 3

40

P420M

420 2)500-66019-20/270,43table 3

30 5)

P420ML1

420 2)500-66019-40/270,43table 3

30 5)

P420ML2

420 2)500-66019-50/270,43table 3

30 5)

P460M

460 2)530-72017-20/270,45table 3

22 5)

P460ML1

460 2)530-72017-40/270,45table 3

22 5)

P460ML2

460 2)530-72017-50/270,45table 3

22 5)

1) Valid for thickness up to 40 mm, for higher thickness refer to the standard
2) Valid for thickness up to 16 mm, for higher thickness refer to the standard
3) For other temperatures under standard refer to the standard
4) On agreement CEV = CEV rovnice ; valid for thickness up to 16 mm, for higher thickness refer to the standard
5) Higher thickness on agreement

PLATES OF STEELS ACCORDING TO ASTM/ASME


DesignationGradeMin. Yield Strength [MPa]Tensile Strength Rm [MPa]Min. Elongation 200/50 [%]Min. Impact Energy KV 1)
[°C/J] - longitudinalDimension Table No

Max. Thickness [mm]

A/SA 204

A255450-58519/232)table 1

80

B275485-62017/212)table 1

80

C295515-65516/202)table 1

80

A/SA 285

A165310-45027/304/14table 1

503)
 

B185345-48525/2810/14table 1

503)

C205380-51523/2716/14table 1

503)

A/SA 387

2310485-62018/222)table 1

80

11310515-69018/222)table 1

80

12275450-58519/222)table 1

80

22310515-690-/182)table 1

80

A/SA 455260515-65515/22-4/18table 1

20 3)

A/SA 515

60 (415)220415-55021/252)table 1

804)

65 (450)240450-58519/232)table 1

804)

70 (485)260485-62017/212)table 1

804)

On agreement, carbon equivalent guarantee is available as per the formula  CEV rovnice
1) Testing on agreement
2) Testing temperature and minimum impact energy on agreement
3) Under standard
4) Higher thickness up to 100 mm on agreement

PLATES OF FINE-GRAIN STEELS ACCORDING TO ASTM/ASME


DesignationGradeMin. Yield Strength [MPa]Tensile Strength Rm [MPa]Min. Elongation 200/50 [%]Min. Impact Energy KV 1)
[°C/J] - longitudinalDimension Table No

Max. Thickness [mm]

A/SA 299

A2904)515-65516/19-7/20table 1

80

B3254)550-690
 16/19-7/20table 2

80

A/SA 302

A310515-65515/192)table 1

80

B345550-69015/182)table 2

80

C345550-69017/202)table 2

80

D345550-69017/202)table 2

80

A/SA 516

55(380)205380-51523/27-51/18table 1

805)

60(415)220415-55021/25-51/18table 1

805)

65(450)240450-58519/23-51/18table 1

805)

70(485)260485-62017/21-46/20table 1

805)

A/SA 537 class 1345485-62018/22-62/20table 1

80

A/SA 612345570-72516/22-46/27table 2

253)

A/SA 662

A275400-54020/23-60/18table 1

503)

B275450-58520/23-51/18table 1

503)

C295485-62018/22-46/20table 1

503)

A/SA 737

B345485-62018/232)table 1

80

C415550-69018/232)table 2

80

On agreement, carbon equivalent guarantee is available as per the formulaCEV rovnice 
1) Testing on agreement
2) Testing temperature and minimum impact energy on agreement
3) Under standard
4) Valid for thickness up to 25 mm, for higher thickness refer to the standard
5) Higher thickness up to 100 mm on agreement



We mainly stock the Plates of following make : 
Azovstal Iron & Steel - Ukraine 
Alchevsk Iron & Steel - Ukraine
 
Ilyich Iron & Steel - Ukraine 
 
ArcelorMittal Steel - Romania
 
Thainox Steel - Taiwan
 
Iscor - South Africa
 
Salzgitter Mannesmann - Germany
 
ThyssenKrupp Steel - Germany
 
ThyssenKrupp Stahl - Germany
 
Dillinger Hutte - Germany
 
Rautaruukki - Finland
 
Voestalphine Grobblech - Austria
 
Corus - U.K
 
Posco - Korea
 
InduSteel - France
 
InduSteel - Belgium
 
SSAB - Sweden
 
Kobe Steel - Japan
 
JFE Steel - Japan
 
Japan Steel - Japan 
 
Nippon Steel - Japan
 
Severstal - Russia
 
SAIL - India
 
Jindal Steel - India
 
TATA Steel - India
 




  © JB Steel, Site designed by www.mesotek.com